banner



How To Replace Window Register And Motor On 03 Century

Introduction

We seek to develop a trouble-gratuitous step-by-step repair guide for a 1999 Buick Century that meets the criteria set by IFIXIT. Not only is our purpose to repair a failed window regulator and motor for personal and security reasons, but too to demonstrate and breakdown to the inexperienced how to make said repair at a more economically inclined price.

Parts

  1. Lower window to about ¾ of the way down or until the frame that the window sits on is visible in the lower opening.

    • Lower window to about ¾ of the manner down or until the frame that the window sits on is visible in the lower opening.

  2. Locate the 3 screws in the door. 1 screw is  in the door latch (phillips head) The other 2 are in the door tray (10mm socket)

    • Locate the iii screws in the door.

    • 1 screw is in the door latch (phillips head)

    • The other 2 are in the door tray (10mm socket)

  3. Pry away the door (a flat head can be used as seen in the image, but any wedge like object would work.)

    • Pry away the door (a flat caput tin can be used as seen in the prototype, but any wedge like object would piece of work.)

  4. Tweeter Connection (circled in red) Disconnect the tweeter connection where the red arrow is pointing.

    • Tweeter Connectedness (circled in red)

    • Disconnect the tweeter connexion where the blood-red arrow is pointing.

    • Automated Lock Connectedness (circled in green)

    • Disconnect the automated lock connectedness from its location in the dark-green circle.

  5. If the internal door panel is covered with protective plastic, remove it before proceeding. If the internal door panel is covered with protective plastic, remove it before proceeding.

    • If the internal door panel is covered with protective plastic, remove it earlier proceeding.

  6. Locate and remove the 3 screws holding the window motor in place (Wrench and 10mm socket needed). Disconnect the window motor connection wiring. Wedge in-between the outer shell of the door and the window to hold the window in place (be careful not to damage the window. May have to stick it in at an angle).

    • Locate and remove the 3 screws belongings the window motor in place (Wrench and 10mm socket needed).

    • Disconnect the window motor connection wiring.

    • Wedge in-between the outer shell of the door and the window to hold the window in identify (exist conscientious not to damage the window. May take to stick it in at an angle).

  7. Locate and Remove the four 10mm screws below the interior door latch. Locate and remove the two 10mm screws on the window frame. Remove the motor and the regulator through the hole.

    • Locate and Remove the iv 10mm screws below the interior door latch.

    • Locate and remove the 2 10mm screws on the window frame.

    • Remove the motor and the regulator through the hole.

  8. Follow steps in reverse order to connect the new window motor and regulator and to reassemble the door panel. Follow steps in reverse order to connect the new window motor and regulator and to reassemble the door panel.

    • Follow steps in reverse order to connect the new window motor and regulator and to reassemble the door panel.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Gear Brothers

Member since: 11/21/2016

191 Reputation

1 Guide authored

0 Comments

How To Replace Window Register And Motor On 03 Century,

Source: https://www.ifixit.com/Guide/1999+Buick+Century+Window+Regulator+and+Motor+Replacement/74107

Posted by: foltzwourt1953.blogspot.com

0 Response to "How To Replace Window Register And Motor On 03 Century"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel